Selective soldering is an automated process for soldering through-hole components only at programmed joints, without putting the whole assembly through a solder wave. The process typically includes precise fluxing, preheat, and soldering with a nozzle (a single-point dip, a drag along a pin row, or a dedicated multi-dip tool), usually under hot nitrogen. It is especially useful on mixed-technology boards, where SMT parts have already been reflowed and connectors or power through-hole parts remain. Compared with hand soldering it offers a programmed, repeatable process. Compared with wave soldering it limits thermal exposure of nearby components.
**Short definition.** Selective soldering is a controlled soldering method that applies flux and molten solder only to the required joints on the solder side of the PCB. The nozzle can dip a single joint, draw along a row of pins, or use a wider or custom tool. Unlike wave soldering, the entire underside of the board is not passed through a solder wave.
What selective soldering is, and when it is the right process
Most SMT lines finish surface-mount parts in reflow. Through-hole parts still remain on many assemblies: connectors that need mechanical strength, power components, transformers, or devices that are not suited to surface mount. Those joints can be soldered by hand, sent through a wave with pallets or masks, or soldered selectively.
In selective soldering the board is held in a fixture or on a conveyor, and the machine follows a program through the three basic stages: flux, preheat and soldering. Each joint, or group of joints, can have its own dwell, wave height, travel speed and nozzle type. That makes it possible to process both a heavy multilayer board and a dense connector row.
The method suits small and medium batches on handload machines, and higher-volume work on modular in-line systems. It is not an automatic replacement for wave soldering in every case. On a board populated only with through-hole parts, a full wave can still be the faster process, because it contacts the entire underside at once.
Selective soldering, wave soldering and hand soldering
| Topic |
Selective soldering |
Wave soldering |
Hand soldering |
| Where solder is applied |
Only at programmed joints |
Across the underside, sometimes with a palleted mask |
By hand, joint by joint |
| Mixed-technology boards (SMT + through-hole) |
Well suited; parts already reflowed are not put through a full wave |
Needs masking, pallets or shields to protect SMT |
Possible, but quality depends on the operator |
| Repeatability |
Programmed control of flux, heat and soldering |
Repeatable on uniform through-hole boards, less flexible per joint |
Depends on skill and tools |
| Thermal load |
More local; preheat reduces thermal shock |
The whole underside is exposed |
Local, and can be uneven |
| Nitrogen |
Common at the soldering point (a hot nitrogen curtain) |
Available on some systems |
Usually not used |
| Throughput |
Slower than a full wave; faster and more consistent than hand soldering in series production |
Fast on all-through-hole boards |
Slow in volume, and needs skilled operators |
| Board design |
Needs nozzle clearance and a suitable pin length |
Needs design for the wave and for any pallet |
Flexible, but hard to reproduce |
Pillarhouse also describes further process benefits: reduced thermal shock, an inert atmosphere that supports wetting and reduces dross, repeatable joints, and a fit for both low-volume and high-volume production, with less dependence on a large team of manual solderers. Machine-specific figures should be taken from the product page, not from this general table.
Process steps: fluxing, preheat and soldering
Most systems follow three clear stages. On a handload machine the board moves between stations inside the cell. On in-line systems, fluxing, preheat and soldering can be split into separate modules to shorten cycle time.
1. Fluxing
Flux removes oxides from the pin and from the plated hole, and prepares the surfaces to wet. In selective soldering, flux is applied only where joints will be made, not across the whole board.
On Pillarhouse systems the standard method is Drop-Jet: a precise deposit of low-solids flux (below 8 percent) from a pressurised, inerted system, intended for no-clean fluxes. Water-soluble flux and ultrasonic fluxing are available according to the model and the application. Accurate deposition matters for hole fill: if flux does not enter the plated barrel, the risk of incomplete fill rises. Excess flux can leave residue or contribute to solder balls.
2. Preheat
Preheat activates the flux, drives off moisture, and brings the assembly closer to soldering temperature so that thermal shock is reduced. Multilayer boards, heavy copper and high thermal-mass components need more energy. Pillarhouse systems commonly use top and/or bottom infrared preheat, in some cases with closed-loop pyrometer control. At the joint itself, the hot nitrogen curtain also provides local preheat.
Public process guides often cite, as a general indication only, a topside board temperature of about 100 to 110 degrees Celsius just before wave contact on double-sided and multilayer boards. The profile must be qualified on the actual assembly. A generic figure should not be copied into a production program.
3. Soldering: single-point, drag, dip and mini-wave
Molten solder reaches the joint through a nozzle. Board layout and cycle time determine which method is used:
- Single-point dip. The nozzle approaches one joint or a small component, dwells, and separates. This suits isolated joints and tight areas, using narrow nozzles.
- Draw or drag. The nozzle travels along a pin row, for example on a connector. Exit speed, angle and peel-off at the end of the row are critical if bridging is to be avoided.
- Multi-dip or custom-dip. A dedicated nozzle tool solders several joints at once. Cycle time falls, but flexibility falls when the product changes.
- Mini-wave or Jet-Wave. A wider nozzle solders an area or a row. Pillarhouse also offers AP nozzles, Jet-Tip and Jet-Wave tools, and a 1.5 mm Micro Nozzle, depending on the model.
Wave-height control, nozzle calibration and the wetting condition of the nozzle itself all affect joint quality. A well-wetted nozzle holds a stable wave. A poorly wetted nozzle loses control of the solder shape.
Nitrogen at the soldering point
On most Pillarhouse systems, soldering takes place under a hot nitrogen curtain at the point of contact. The inert atmosphere reduces oxidation of the molten solder, supports wetting, and reduces dross. According to the manufacturer's product pages, the required nitrogen purity is typically 99.995 percent or better (on the Pilot: 99.99 percent or better), at a supply pressure of 5 bar, with consumption depending on the model and nozzle (for example about 30 litres per minute on the Pilot, and a range of 30 to 100 litres per minute on other models).
Nitrogen does not replace correct preheat or a suitable flux. Flow and purity must match the machine and the qualified process. The Pilot can be specified with a nitrogen generator built into the machine stand. The PillarGEN range offers dedicated generators in 30, 40 and 80 versions.
Design guidance for boards that will be selectively soldered
Joint quality starts in design. Public design and process guides repeat several practical rules. The figures below are orientation only and must be confirmed against the board, the nozzle and the machine.
- Nozzle clearance. Joints need an access area free of nearby SMT parts, and preferably free of vias or test points that could be wetted by mistake. Tight clearance is a common cause of bridges and damage to parts that have already been reflowed.
- Lead protrusion. If the pin is too short, the meniscus may be weak. If it is too long, bridging risk rises, especially on fine-pitch rows. Published guides do not agree on a single length, because it depends on the method: for a single-nozzle drag on a tight pitch, a short protrusion on the order of 1 mm is often recommended; for multi-nozzle dip soldering, some guides recommend 2.0 to 2.5 mm to improve heat transfer. There is no single value for every board.
- Pin pitch. Dense rows need more attention to layout, wetting and peel-off. One design guide cites a practical minimum pitch of about 1.27 mm for single-nozzle mini-wave soldering, with extra care below about 2.2 mm.
- Hole-to-pin ratio. A common rule of thumb is a hole diameter 0.2 to 0.4 mm larger than the pin. A ratio that is too tight makes flux penetration harder. A ratio that is too open weakens capillary action and can produce a sunken joint.
- Thermal relief. Pads tied directly into heavy copper lose heat quickly and fill less reliably. A thermal relief keeps energy in the pad.
- Stand-off under the component body. A gap is needed so that solder can rise through the hole and form a topside meniscus.
- Solder mask. Mask that sits too close to the joint can add to solder balling and can pull heat away from the pad.
- Soldering direction. On connectors and pin rows, plan a travel path that allows a clean exit at the end of the row, sometimes diagonally, or with the wave switched off at the end of the stroke.
Typical defects and how to address them
The table below summarises faults that recur in published troubleshooting guides. The actions are starting points for a qualified process, not a fixed recipe.
| Defect |
Common causes |
What to check first |
| Insufficient hole fill |
Too little flux, or flux that does not enter the hole; low preheat; low solder temperature; a tight hole-to-pin ratio; too large a gap between the wave and the board |
Confirm flux volume and head height, raise the preheat profile, verify bath temperature and wave height, and review the hole design |
| Bridging |
Pins that are too long; tight pitch; a poor exit from the end of a connector; travel that is too fast; poor nitrogen purity; insufficient heat |
Shorten pins where the design allows, improve peel-off, check nitrogen and heat, and reduce oversized pads in tight spaces |
| Icicles or excess solder |
An unsuitable separation move; low temperature; high speed; long pins |
Adjust exit speed and angle, confirm temperature, and consider switching the wave off at the end of the connector |
| Solder balls |
More common in selective soldering than in wave soldering, in part because of higher local temperatures; too much flux; low preheat; unsuitable nitrogen flow; solder-mask type |
Adjust flux and preheat, check nitrogen flow, and review mask clearance around the pad |
| Blow holes and sunken joints |
Moisture in the board; low preheat; a hole that is too large for the pin; outgassing from the hole |
Dry boards to the applicable procedure, improve preheat and flux, and review the hole-to-pin ratio |
| Shorts next to SMT parts |
Too little nozzle clearance; large pads; poor solder drainage |
Improve keep-out design, reduce pads where possible, and check flux and the thermal profile |
Nozzle and bath maintenance belong to the same discussion. An oxidised or worn nozzle harms wetting and wave stability. The manufacturer stresses that a clean interface between the solder and the nozzle is essential for process control.
Relevant IPC points
Through-hole solder joints are usually accepted against IPC-A-610, the acceptability standard for electronic assemblies. Process requirements for soldering are set out in IPC J-STD-001. This article is not a substitute for the official text of either standard, or for the customer's quality requirements.
Public industry discussions of IPC-A-610 often refer to a vertical fill criterion for supported holes, with differences between product classes and with defined exceptions in some classes. The applicable fill percentage, fillet shape and any exception must be read in the standard that governs the product, not copied from a secondary summary. The process still has to be qualified on the actual assembly: a thermal profile, flux verification, a first article, and visual or other agreed inspection.
On in-line systems, the manufacturer's Orissa Synchrodex Pro page states that the conveyor is compatible with IPC-SMEMA-9851, the usual interface standard for linking machines in an SMT line. That compatibility concerns line integration. It does not replace joint-acceptance criteria.
How to choose a selective soldering system
The choice follows the board, the batch size and the place in the line, not the model name alone. Useful working questions include:
- Board size and keep-out. What are the board or pallet dimensions, and what clearance is needed above and below the board.
- Handload or in-line. Small batches and high mix usually fit a handload machine. Higher throughput and a continuous line point to a modular or in-line system, with room to add flux, preheat and solder cells.
- Joint count and cycle time. Isolated joints can use a single-point nozzle. Long connectors benefit from a drag. If cycle time is critical, a multi-dip tool or several solder cells in parallel may be needed.
- One alloy or two. A need to run leaded and lead-free work, or two nozzle sizes, at the same time leads to a duplex bath or to a rapid bath change.
- Preheat. Multilayer boards and water-based fluxes often need bottom-side heat, top-side heat, or both, with closed-loop temperature control.
- Nitrogen and maintenance. Is nitrogen already available in the plant, or is a built-in or external generator required. Access to the bath, wave-height calibration and a process camera also matter.
- Software and offline programming. Point-and-click programming on a board image, plus an offline package that uses Gerber data, shortens setup without stopping the machine.
ASI Technologies can help match the configuration to your boards, against the Pillarhouse range presented on the site.
Pillarhouse systems on the ASI site
According to Pillarhouse International's world agents page for Israel, ASI Technologies is the manufacturer's contact in Israel. The ASI sites present the Pillarhouse selective soldering range in the Selective Soldering category.
Pillarhouse was founded in 1978 in Chelmsford, UK. According to the manufacturer, its first production soldering system appeared in 1984, and in 1994 it developed the world's first selective soldering machine. Design and manufacturing remain headquartered in Chelmsford.
According to the manufacturer's official products page, the current range is grouped into handload, index handload, in-line and modular in-line systems, plus nitrogen generators. The figures below are taken from the manufacturer's product pages, and were checked on 17 November 2026. Binding details should be confirmed on the manufacturer page and on the matching ASI product page.
Handload
- Pilot. An entry-level benchtop, handload, single-point system for small to medium batches. Board size up to 330 × 250 mm, 6 kg solder pot, AP nozzles and a 1.5 mm Micro Nozzle, Drop-Jet fluxer as standard, a hot nitrogen curtain, and optional bottom-side IR preheat. Software: PillarCOMMX Lite.
- Jade MKII. A flexible entry-level handload, single-point system. Board size up to 457 × 508 mm, 8 kg solder pot, hot nitrogen curtain, Drop-Jet fluxer, and PillarCOMMX software with optional offline programming through PillarPAD.
- Jade Pro. A flexible offline system with a Duplex pair of solder baths on independent Z axes. This allows two nozzle sizes, or two alloys, in the same program. Board size up to 457 × 508 mm, 20 kg standard pot (30 kg large bath).
Index handload
- Jade Handex. A rotary table with two work positions, so that a board can be loaded and unloaded while another is processed. Board size up to 457 × 508 mm, 15 kg solder pot (25 kg large bath).
- Jade Prodex. An offline system with a twin-board rotary table and a Duplex twin-bath arrangement. Board size up to 457 × 508 mm, 20 kg pot (30 kg large bath). It is intended for alloy or nozzle changes without a long interruption to flow.
In-line and modular
- Orissa Fusion. A high-speed, multi-cell in-line system. Fusion Compact (three stations) and Fusion Standard (four stations) can be configured with fluxing, preheat and one or more solder cells. The standard board size is up to 381 × 430 mm, with a larger size available depending on the configuration. The platform supports the manufacturer's nozzle technologies, including the 1.5 mm Micro Nozzle, Jet-Wave and dedicated dip tools.
- Orissa Synchrodex Pro. A modular in-line system for high throughput and flexible cell layouts. Flux, preheat and solder modules can be added along the line. In standard configurations it handles boards from 102 × 102 mm up to 420 × 610 mm or 610 × 610 mm, and up to 1200 × 610 mm in the XL frame. The 1600 mm module can run a single bath or a dual bath. The conveyor is compatible with IPC-SMEMA-9851. Software: PillarCOMM.NET, with offline programming from Gerber data.
The official products page also lists Orissa Synchrodex and Orissa Synchrodex Combo in the modular range. No separate ASI product pages for those two models were found at the time of this draft. The ASI site also has a page for the Jade MK IV. That model did not appear on the manufacturer's official products page at the time of the check, so no specifications are given for it here.
Software, flux and nitrogen
- PillarPAD. An offline process programming package, used to prepare programs away from the machine.
- PillarDOT. A Drop-Jet head for precise flux deposition.
- PillarGen 30/40/80. Nitrogen generators in the PillarGEN series, as listed by the manufacturer.
Repeatability of ±0.05 mm, axis resolution and other service data should be read on the manufacturer page and on the ASI product page. According to the manufacturer, the machines are compatible with commonly used solder alloys, including lead-free.
Frequently asked questions
What is selective soldering, in one sentence?
It is automated, controlled soldering of through-hole components only at chosen joints, using flux, preheat and a solder nozzle, usually under nitrogen, without putting the whole board through a full wave.
When should we choose selective soldering instead of wave or hand soldering?
When the board mixes SMT and through-hole parts, when you need more repeatability than hand soldering can offer, or when a full wave would need complex masking and would expose sensitive parts. Wave soldering remains efficient on all-through-hole boards where throughput is the priority. Hand soldering remains relevant for rework, prototypes and very small quantities.
Why is nitrogen used in selective soldering?
Nitrogen creates an inert atmosphere around the molten solder, reducing oxidation and dross and supporting wetting. On Pillarhouse systems the nitrogen is also heated, which preheats the joint locally and reduces thermal shock. It does not replace the correct flux or preheat.
Which design rules matter most before we order a machine or release a new board?
Nozzle access clearance, pin length matched to pitch and to the soldering method, a sensible hole-to-pin ratio, thermal relief in heavy copper, and a gap between the component body and the board. It is better to involve the equipment supplier at the design stage, not after the board is frozen.
What are the most common defects, and what should we check first?
Incomplete hole fill usually points to flux or preheat. Bridges and icicles are often linked to pin length, pitch and the exit move from the joint. Solder balls can relate to flux, heat, nitrogen or the solder mask. Start by verifying process parameters, and change the design only after that.
Are the systems compatible with lead-free soldering?
Yes. Pillarhouse product pages for the machines described here state compatibility with commonly used alloys, including lead-free. A lead-free alloy usually needs tighter discipline on temperature, nitrogen and nozzle care.
How does a handload machine differ from an in-line system?
A handload machine, such as the Pilot or a Jade system, suits small and medium batches and high flexibility, with the board loaded by hand. An in-line system, such as Orissa Fusion or Orissa Synchrodex Pro, sits on a conveyor line, can be expanded with extra modules, and is intended for higher throughput and continuous work.
Who represents Pillarhouse in Israel, and how do we get in touch?
According to the manufacturer's world agents page, ASI Technologies is the contact in Israel. You can reach the team through the contact form, by phone on +972-8-9208844, or by email at contact@asi-tech.co.il. Address: Netzer Sereni, 7039500, Israel.
Talk to ASI about a suitable configuration
If you are designing a board with through-hole parts, moving work off the soldering iron, or choosing a machine for a new line, the ASI team can review your assemblies and production volume against the Pillarhouse range. We will come back with a configuration direction, without committing you to a model in advance.
Contact ASI · +972-8-9208844 · contact@asi-tech.co.il