ASI Technologies – distributor in Israel of Chemours Opteon™ fluids.
Opteon™ SF33 is a clear, colorless, nonflammable Chemours specialty fluid based on HFO-1336mzz-Z, with zero ozone depletion potential (ODP 0) and a very low global warming potential (GWP 2). Its 33.4 °C boiling point and low surface tension provide good wetting and fast drying.
Chemours specifies SF33 for precision cleaning, metal degreasing, electronics cleaning and rinsing, as an aerosol solvent and for lubricant deposition, and as a heat transfer fluid for two-phase direct-to-chip cooling.
An alternative to legacy solvents and 3M Novec™
According to Chemours, Opteon™ SF33 is suitable for replacing PFCs, HCFCs, PFPEs, HFCs and HFEs in industrial solvent applications. Since 3M announced the discontinuation of Novec™ and Fluorinert™ fluids by the end of 2025, cross-reference charts from international distributors list SF33 as an alternative to Novec™ 7100 and 7200 (MicroCare) and Novec™ 7000 (TMC Industries).
Note: SF33 is a different chemistry (HFO) from Novec™ HFE fluids, so every changeover requires a process and materials compatibility check. Need a same-chemistry (HFE) replacement? See ASI-7100 and ASI-7200. For the full comparison, see our Novec™ replacement guide.
Sources: Chemours (opteon.com), 3M (announcement of 20 Dec 2022), MicroCare, TMC Industries. Novec™ and Fluorinert™ are trademarks of 3M.
Material compatibility
- Metals: compatible with most metals. Stainless steel, copper, brass, aluminum and carbon steel were tested at 100 °C for two weeks, with no change.
- Plastics: compatible with most plastics.
- Elastomers: compatible with most elastomers; some reversible swelling is expected with partially fluorinated elastomers.
- Not recommended with strong bases, strong Lewis acids (e.g., aluminum trichloride), alkali and alkaline earth metals, powdered metals and powdered metal salts.
Packaging available in Israel
| ASI P/N |
Pack |
| 30368 |
23 kg pail |
| 30369 |
250 kg drum |
Storage: store in a clean, dry area, protected from freezing and not above 46 °C. Drum pumps are recommended.
For technical advice and a quote: +972-8-3760650. More information: Chemours Opteon™ specialty fluids in Israel.
FAQ
What is Opteon™ SF33?
A Chemours specialty fluid based on HFO-1336mzz-Z (CAS 692-49-9). It is nonflammable, with GWP 2, ODP 0 and a 33.4 °C boiling point.
Is Opteon™ SF33 flammable?
No. It has no flash point (ASTM D56/D1310) and no vapor flammability (ASTM E681). According to Chemours, it is not classified as a flammable liquid by NFPA or DOT.
Can SF33 be used for server cooling?
Chemours specifies SF33 as a heat transfer fluid for two-phase direct-to-chip cooling. Suitability for a specific system is evaluated with the manufacturer's data, and ASI supports that evaluation.
What is the difference between SF33 and SF80?
SF33 is a pure HFO with Kb 11.3 and a 33.4 °C boiling point, used for precision cleaning, rinsing, aerosols and cooling. Opteon™ SF80 is a t-DCE blend with Kb 99 and a 47 °C boiling point, used for vapor degreasing and the removal of oils, flux and silicone.
Does SF33 replace Novec™ 7100?
Chemours states that SF33 can replace HFEs and other solvents, and international distributors' charts list it as an alternative to Novec™ 7100 and 7200. It is a different chemistry, so a compatibility check is required. For a same-chemistry replacement, see ASI-7100.
Which pack sizes are available in Israel?
23 kg pail (P/N 30368) and 250 kg drum (P/N 30369).
How do I get the technical bulletin?
From the Downloads tab on this page, or from the ASI team.